A Step-by-Step Overview to Installing a Bath Tub
Additional ResourcesWhat are your opinions on Installing A Bathtub?
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to vacate the old tub and embeded in the brand-new one. Ensure you have actually qualified on your own for the work as well as fit attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to transform the arrangement of your previous water supply pipes.
Your devices and material list should make up the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the tub and likewise check the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bathtub must wait until the tub has actually been used at the very least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about difficulties with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that entry on How to Install a Bathtub when exploring the search engines. Are you aware of somebody else who is fascinated about the niche? Do not hesitate to share it. Thanks for your time. Don't hesitate to come by our site back soon.
Call Today